国产精品18久久久久久白浆色欲_在线观看电影院欧美日韩电影_最近免费MV在线观看_国产精彩三级黄色毛片_国产精品大陆AV专区_亚洲日韩va在线视频_本子全彩h爆乳无遮挡亚丝娜_中文无码视频在线观看_人妻少妇乱子伦精品无码专区电影_欧美强奸a级电影久久

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

vehicle hydraulic cylinder Sold to Poland

Release time:2023-11-06 22:53:44 Hits: Current position: Home > News

This article mainly introduces:

Poland vehicle hydraulic cylinder,vehicle hydraulic cylinder manufacturer

Poland vehicle hydraulic cylinder

(Poland vehicle hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

vehicle hydraulic cylinder are widely used in Poland,because of long service life,smooth movement,high work efficiency.So our company has designed vehicle hydraulic cylinder for customers from Poland.

Introduction to vehicle hydraulic cylinder:

In the case of serious wear on the inner surface of the vehicle hydraulic cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the vehicle hydraulic cylinder manufacturing process for replacement. The vehicle hydraulic cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

How to determine the working pressure of the vehicle hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, vehicle hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

When using the vehicle hydraulic cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the vehicle hydraulic cylinder block. If the vehicle hydraulic cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the vehicle hydraulic cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the vehicle hydraulic cylinder, so that the working efficiency of the vehicle hydraulic cylinder is reduced.

When the vehicle hydraulic cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

Answers to some questions about vehicle hydraulic cylinder:

How to remove the lifting cylinder from the forklift truck?
The lifting cylinder is generally fixed on the door frame, and there are screws under and above it, and it is OK to loosen the screws with a wrench on the top. However, we must pay attention to ensure safety and prevent damage to the cylinder or safety accidents.

What is st represented in the cylinder formula?
St is the original unit of kinematic viscosity, the abbreviation of Stokes, that is, Stokes, short for S. cm2/s has now been used. 1 s (St) = 10^-4m2/s.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP