国产精品18久久久久久白浆色欲_在线观看电影院欧美日韩电影_最近免费MV在线观看_国产精彩三级黄色毛片_国产精品大陆AV专区_亚洲日韩va在线视频_本子全彩h爆乳无遮挡亚丝娜_中文无码视频在线观看_人妻少妇乱子伦精品无码专区电影_欧美强奸a级电影久久

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Dominica

Release time:2023-11-23 08:22:13 Hits: Current position: Home > News

This article mainly introduces:

Dominica hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Dominica synchronous hydraulic cylinder

(Dominica synchronous hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

synchronous hydraulic cylinder are widely used in Dominica,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed synchronous hydraulic cylinder for customers from Dominica.

Introduction to synchronous hydraulic cylinder:

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular synchronous hydraulic cylinder action. Troubleshooting method: Replace the rubber hose.

The scar on the sliding surface of the synchronous hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the synchronous hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

If the seal of the synchronous hydraulic cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Most of the failure of the synchronous hydraulic cylinder is because there is a foreign body in the synchronous hydraulic cylinder into the failure of the synchronous hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the synchronous hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about synchronous hydraulic cylinder:

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

What valve is used to control cylinder expansion?
Mainly use reversing valve, but the details of the control need hydraulic control valve, hydraulic control valve can be divided into direction control valve, pressure control valve, flow control valve. The valve controls the expansion of the cylinder is the direction control valve, that is, the reversing valve. What is the meaning of two-position three-way and three-position four-way of the reversing valve? Usually according to the different working positions that can stay after the spool is moved, it can be divided into: two-position valves, three-position valves and multi-position valves. According to the number of different slide valve channels can be divided into: two-way valve, three-way valve, four-way valve, five-way valve and multi-way valve. The name of the reversing valve is called the multi-position and multi-pass reversing valve according to its working position and the number of channels.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP